Aussie Owned & Operated

Pre-Made Kits to suit every application

Our Service Difference

Sale!

Victron Smart BatteryProtect 12/24V-220A

$180.00 (inc. GST)

The Victron Smart BatteryProtect 12/24V-220A is a battery protection device designed to protect your battery from over-discharge, over-voltage, and other potential problems. It can be used with 12 or 24V battery systems and can handle up to 220A of current.

SKU: BPR122022000 Categories: ,

Victron smart BatteryProtect:

The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. The on/off input can be used as a system on/off switch.

Features:

12/24V auto ranging- The Smart BatteryProtect automatically detects system voltage one time only.

Bluetooth: programming made easy- When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set. Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual). If required, Bluetooth can be disabled.

A special setting for Li-ion batteries- In this mode the BatteryProtect can be controlled by the VE.Bus BMS.

Note: the BatteryProtect can also be used as a charge interrupter in between a battery charger and a Li-ion battery. See connection diagram in the manual.

Ultra-low current consumption- This is important in case of Li-ion batteries, especially after low voltage shutdown. Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information.

Over voltage protection- To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16.3V respectively 32.6V.

Ignition proof- No relays but MOSFET switches, and therefore no sparks.

Delayed alarm output- The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay.

Delayed load disconnect and delayed reconnect- The load will be disconnected 90 seconds after the battery voltage drops below the preset level. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage.

Additional information

Smart BatteryProtect

Smart BP-220

Maximum continuous load current

220A

Peak current (during 30 seconds)

600A

Operating voltage range

6 –35V

Current consumption BLE on /off

When on: 1,4 mA When off or low voltage shutdown : 0,9 mA

When on: 1,2 mA When off or low voltage shutdown : 0,7 mA

Alarm output delay

12 seconds

Max. load on alarm output

50 mA (short circuit proof)

Load disconnect delay

90 seconds (immediate if triggered by the VE.Bus BMS)

Load reconnect delay

30 seconds

Default thresholds

Disengage: 10,5V or 21V Engage: 12V or 24V

Operating temperature range

Full load: -40°C to +40°C (up to 60% of nominal load at 50°C)

Connection

M8

Weight

0,8 kg 1.8 lbs

Dimensions (HxWxD)

62x123x120mm

2.5 x 4.9 x 4.8inch

Download

Datasheet-Smart-Battery-Protect-65-A–100-A–220-A-EN-Victron smart BatteryProtect 12/24V 220A spec Sheet-

Manual-Smart-Battery-Protect-12V-24V-65-A-100-A–220-A-EN-NL-FR-SV-DE-PT-ES-IT-TRVictron smart BatteryProtect 12/24V 220A manual-