Aussie Owned & Operated

Pre-Made Kits to suit every application

Our Service Difference


Victron BlueSolar PWM-LCD&USB 48V-30A

Original price was: $160.00.Current price is: $145.45. (inc. GST)


The Victron BlueSolar PWM-LCD&USB 48V-30A is a charge controller designed to regulate the charging of batteries from solar panels. Here are some key features and specifications of this product:

  • Maximum solar panel input voltage: 100V
  • Maximum charging current: 30A
  • Maximum PV power, 12V system: 400W
  • Maximum PV power, 24V system: 800W
  • Maximum PV power, 48V system: 1600W
  • 3-stage PWM charging algorithm with temperature compensation
  • LCD display for system status information
  • USB port for charging devices such as phones or tablets
  • Automatic load disconnect to prevent over-discharging of the battery
  • Reverse polarity protection
  • Over-temperature protection

Overall, the Victron BlueSolar PWM-LCD&USB 48V-30A is a reliable and versatile charge controller that is suitable for a range of solar charging applications, particularly in off-grid systems. The LCD display and USB port are convenient features that make it easy to monitor and use the system.

SKU: SCC040030050 Categories: ,

Victron Bluesolar LCD & USB PWM solar controller:

Victron's range of  PWM and MPPT charge controllers are both widely used to charge batteries with solar power.

The PWM controller is in essence a switch that connects a solar array to the battery. The result is that the voltage of the array will be pulled down to near that of the battery.

A PWM controller is not a DC to DC transformer. The PWM controller is a switch which connects the solar panel to the battery. When the switch is closed, the panel and the battery will be at nearly the same voltage. Assuming a discharged battery the initial charge voltage will be around 13 V, and assuming a voltage loss of 0,5 V over the cabling plus controller, the panel will be at Vpwm = 13,5 V.

The voltage will slowly increase with increasing state of charge of the battery. When absorption voltage is reached the PWM controller will start to disconnect and reconnect the panel to prevent overcharge (hence the name: Pulse Width Modulated controller).


Liquid crystal display- For status monitoring and set-up

Load output- Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable.

Day/night timing of the load output- This option allows for a pre-set ON-time after dusk.

Programmable battery charge algorithm- Preprogrammed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only)

Two 5 Volt USB outputs- Maximum current (both outputs combined): 2A

Additional information

BlueSolar PWM-Light


Battery Voltage


Rated charge current


Automatic load disconnect


Maximum solar voltage

100 V


< 10 mA

Load output

Manual control + low voltage disconnect + timer


Battery reverse polarity(fuse) Output short circuit Over temperature

Overload protection

Shut down after 60 s in case of 130% load

Shut down after 5 s in case of 160% load

Short circuit: immediate shut down


Common positive

Operating temp. range

-35 to +60°C (full load)

Humidity (non-condensing)

Max 95%

Charge voltage 'absorption'


Charge voltage 'float'


Low voltage load disconnect


Low voltage load reconnect


Protection class


Terminal size

16 mm² / AWG6



Dimensions (h x w x d)

101 x 184 x 47mm


IEC 62109-


EN 61000-6-1, EN 61000-6-3 ISO 7637-2


Datasheet-BlueSolar-Charge-Controllers-12-24V-LCD&USB-EN (6)Victron BlueSolar PWM-LCD&amp;USB 48V-30A